First of all, it is illegal to replace the engine without permission, and the car cannot be examined. If the traffic police find it, the car will be detained, and the insurance will not take effect. Regulations only allow the replacement of the same model of engine. Secondly, many parts of 6T and 0T are not universal, and transplantation is also a big project, which is not much cheaper than buying 328i directly.
The gasoline adsorbed on the carbon after landing will be sucked into the cylinder by the engine and burned, and the mixed gas will thicken. The mixed gas is sometimes thin and sometimes thick, which will cause idle shaking after cold start. The lower the temperature, the greater the amount of oil required for cold start, the more the presence of carbon accumulation will affect the cold start.
cylinder. BMW n13b16The A engine uses a four-cylinder engine. The development history of the BMW four-cylinder engine can be traced back to the engine equipped with the BMW 3/15 model in 1927. The four-cylinder engine is 180 degrees, the six-cylinder engine is 120 degrees, and the engine runs more densely.
Generally, timing marks are marked on the timing gear, front end of the crankshaft and flywheel of the engine. The meaning of the mark is the position of the stop point on the piston of the first cylinder of the engine. With this position, we can easily proofread the timing.
Both models are equipped with the BMW N13B16A 6-liter single-turbo twin-swirl tube supercharged direct injection engine. The maximum power of 116i is 100 kilowatts (136 horsepower) and the maximum torque is 220 Nm; the maximum power of 118i is increased to 125 kilowatts (170 horsepower) and the maximum torque is 250 Nm.
I think the N13B16A is still a great X. After all, it is a 6T high-power version of the supercharged engine released by BMW. The 118I uses this one, which is powerful and fuel-efficient. Secondly, THP160, PSA's newly introduced domestic one, is used in C4L and 3008. The power parameters are also very good, and the speed is rapid, but the fuel consumption is slightly higher.
1. Consider the carbon accumulation in the combustion chamber. Insufficient fuel combustion: When the oil supply of the pump oil is greater than that of the combustion chamber for a long time, the fuel burned by the combustion chamber will form carbon. Before each shutdown, the gear needs to be adjusted to the minimum, so that the fuel supply is relatively small, so that the fuel in the machine can be fully burned. When shut down, the precipitation of carbon accumulation will be reduced.
2. It is difficult for ordinary car owners to distinguish which are faulty and which are reasonable. When I went to the repair shop to test the abnormal sound of the vehicles, only nearly 20% of the vehicles really had problems.
3. Serious carbonization of the engine. The most common reason for engine shaking and idling is excessive carbon accumulation in the fuel injection nozzle. What is carbon accumulation? Carbon accumulation is formed when fuel and air are mixed in the intake system, and some carbon dirt will be attached to sealed areas such as the fuel injector and the top of the piston.
4. There are many reasons for engine shaking: empty air, dirty filter, high-voltage line disconnection, abnormal water temperature, fuel injector blockage, carbon accumulation, grease blockage, etc., which may cause engine shaking. It is recommended that you contact the local 4S store for inspection and maintenance.
1. There are several reasons for the engine shaking of the BMW n13b16a: the engine cylinder is missing: the engine cylinder lack mainly refers to the abnormal operation of one or more cylinders of the engine, generallyIt is manifested as the obvious intermittent flow of exhaust gas discharged by the car. At the same time, the exhaust pipe shakes seriously, and the engine shaking can be clearly felt, sometimes accompanied by a sudden noise.
2. When the vehicle starts, if the engine cold start idle is unstable, it will cause abnormal shaking of the car body. There are many reasons for this situation, including excessive carbon accumulation in the fuel injector, serious carbon accumulation in the engine, serious aging of engine parts, dirty throttle valve, problems with the ignition system, unstable oil pressure of the car, etc.
3. It is difficult for ordinary car owners to distinguish which are faulty and which are reasonable. When I went to the repair shop to test the abnormal sound of the vehicles, only nearly 20% of the vehicles really had problems.
What is the reason for the engine shaking of BMW n13b16a?Import restrictions by HS code category-APP, download it now, new users will receive a novice gift pack.
First of all, it is illegal to replace the engine without permission, and the car cannot be examined. If the traffic police find it, the car will be detained, and the insurance will not take effect. Regulations only allow the replacement of the same model of engine. Secondly, many parts of 6T and 0T are not universal, and transplantation is also a big project, which is not much cheaper than buying 328i directly.
The gasoline adsorbed on the carbon after landing will be sucked into the cylinder by the engine and burned, and the mixed gas will thicken. The mixed gas is sometimes thin and sometimes thick, which will cause idle shaking after cold start. The lower the temperature, the greater the amount of oil required for cold start, the more the presence of carbon accumulation will affect the cold start.
cylinder. BMW n13b16The A engine uses a four-cylinder engine. The development history of the BMW four-cylinder engine can be traced back to the engine equipped with the BMW 3/15 model in 1927. The four-cylinder engine is 180 degrees, the six-cylinder engine is 120 degrees, and the engine runs more densely.
Generally, timing marks are marked on the timing gear, front end of the crankshaft and flywheel of the engine. The meaning of the mark is the position of the stop point on the piston of the first cylinder of the engine. With this position, we can easily proofread the timing.
Both models are equipped with the BMW N13B16A 6-liter single-turbo twin-swirl tube supercharged direct injection engine. The maximum power of 116i is 100 kilowatts (136 horsepower) and the maximum torque is 220 Nm; the maximum power of 118i is increased to 125 kilowatts (170 horsepower) and the maximum torque is 250 Nm.
I think the N13B16A is still a great X. After all, it is a 6T high-power version of the supercharged engine released by BMW. The 118I uses this one, which is powerful and fuel-efficient. Secondly, THP160, PSA's newly introduced domestic one, is used in C4L and 3008. The power parameters are also very good, and the speed is rapid, but the fuel consumption is slightly higher.
1. Consider the carbon accumulation in the combustion chamber. Insufficient fuel combustion: When the oil supply of the pump oil is greater than that of the combustion chamber for a long time, the fuel burned by the combustion chamber will form carbon. Before each shutdown, the gear needs to be adjusted to the minimum, so that the fuel supply is relatively small, so that the fuel in the machine can be fully burned. When shut down, the precipitation of carbon accumulation will be reduced.
2. It is difficult for ordinary car owners to distinguish which are faulty and which are reasonable. When I went to the repair shop to test the abnormal sound of the vehicles, only nearly 20% of the vehicles really had problems.
3. Serious carbonization of the engine. The most common reason for engine shaking and idling is excessive carbon accumulation in the fuel injection nozzle. What is carbon accumulation? Carbon accumulation is formed when fuel and air are mixed in the intake system, and some carbon dirt will be attached to sealed areas such as the fuel injector and the top of the piston.
4. There are many reasons for engine shaking: empty air, dirty filter, high-voltage line disconnection, abnormal water temperature, fuel injector blockage, carbon accumulation, grease blockage, etc., which may cause engine shaking. It is recommended that you contact the local 4S store for inspection and maintenance.
1. There are several reasons for the engine shaking of the BMW n13b16a: the engine cylinder is missing: the engine cylinder lack mainly refers to the abnormal operation of one or more cylinders of the engine, generallyIt is manifested as the obvious intermittent flow of exhaust gas discharged by the car. At the same time, the exhaust pipe shakes seriously, and the engine shaking can be clearly felt, sometimes accompanied by a sudden noise.
2. When the vehicle starts, if the engine cold start idle is unstable, it will cause abnormal shaking of the car body. There are many reasons for this situation, including excessive carbon accumulation in the fuel injector, serious carbon accumulation in the engine, serious aging of engine parts, dirty throttle valve, problems with the ignition system, unstable oil pressure of the car, etc.
3. It is difficult for ordinary car owners to distinguish which are faulty and which are reasonable. When I went to the repair shop to test the abnormal sound of the vehicles, only nearly 20% of the vehicles really had problems.
What is the reason for the engine shaking of BMW n13b16a?HS code-driven cost variance analysis
author: 2024-12-24 20:51Machinery exports HS code insights
author: 2024-12-24 20:18Steel pipes (HS code ) trade insights
author: 2024-12-24 19:42How to adapt to shifting trade policies
author: 2024-12-24 18:56Trade data-driven market penetration
author: 2024-12-24 18:28Export quota monitoring software
author: 2024-12-24 20:31Trade data for import tariff planning
author: 2024-12-24 19:38Cross-border HS code harmonization
author: 2024-12-24 18:52HS code validation for diverse industries
author: 2024-12-24 18:45Global trade data harmonization
author: 2024-12-24 18:07591.44MB
Check933.85MB
Check272.74MB
Check262.29MB
Check912.48MB
Check777.18MB
Check711.29MB
Check228.83MB
Check426.41MB
Check438.25MB
Check642.12MB
Check465.75MB
Check458.54MB
Check215.64MB
Check321.97MB
Check422.79MB
Check212.46MB
Check133.78MB
Check464.67MB
Check825.27MB
Check869.45MB
Check634.74MB
Check896.85MB
Check927.26MB
Check426.68MB
Check732.14MB
Check457.94MB
Check415.27MB
Check113.23MB
Check146.26MB
Check212.34MB
Check911.89MB
Check317.94MB
Check183.62MB
Check276.13MB
Check644.93MB
CheckScan to install
Import restrictions by HS code category to discover more
Netizen comments More
2651 How to identify correct HS codes
2024-12-24 20:39 recommend
2163 Top-rated trade data platforms
2024-12-24 19:25 recommend
141 Global trade certification services
2024-12-24 18:51 recommend
558 Industrial spare parts HS code mapping
2024-12-24 18:48 recommend
1028 Trade data-driven contract negotiations
2024-12-24 18:14 recommend