Real-time shipment data alerts

List of the catalog of this article:

• 1, How to disassemble the interior panel of the car door?
• 2
  、 Will the interior panel of the car tailgate leak water if it is loose?
• 3, What is the method to solve the problem of untightening the interior panel of the door
• 4, How to disassemble the interior panel of the car door?
• 5, How to disassemble the interior panel of the car

How to disassemble the interior panel of the car door?

The steps for disassembly of the door trim of Rena car are as follows: prepare tools and work carts or workbench frames. Open the door as much as possible to make the hinge bracket easier to operate. Install a bracket on the lower edge of the door to support the weight of the door, protect the door, and unstwew the window glass.

Use a screwdriver or plastic tool to gently remove the cover on the door handle and unscrew the screws. To remove the panel of the window controller, you usually need to use plastic tools to gently move the panel and remove the screws. Use a plastic tool to gently remove the edge of the interior panel of the door and gently pull out the board.

How to remove the Audi a6 door trim panel A6 Audi door trim panel disassembly: unscrew the door lock button, hold the hand trim backwards and down, pry the door handle trim cover and unscrew the Phillips screw, pry open the glass lifting control panel from the edge up, and unplug the wire harness.

First, use a flat-mouth screwdriver to pry the trim panel under the door handle, pry it down from the middle, and then pull it out and pry the first half. Then unplug the plug of the window lift switch. You need to hook the card from the back with your finger before you can unplug it.

Disassembly tools are ready. First of all, you need to prepare the tools used in the whole process of disassembling the interior panel of the Tuan door, two cones (one for each size), one t-25 spline, and one t-30 spline. Disassembly of the door glass lifting switch.

Will the interior panel of the car tailgate leak water if it is loose?

will. The water leakage point of the trunk is caused by the water leakage at the rear bolt snap, or the aging of the snap at the taillight and the original sealing ring. If the snap or sealing ring is damaged, the sealing of the trunk will be affected, resulting in water leakage.

Glue the loose waterproof strip and re-glue it with a special adhesive. Restore the sealing performance so that it will no longer leak rain. Please also pay attention to the aging of the waterproof strip in the old car. Most of the reasons for the rain leakage around the door are the waterproof strips glued around, and check whether there is any breakage or peeling.

Clean it up and won't rust.The rubber edge of the trunk generally does not leak water, unless there is an accident that is not repaired or the glue edge is aging and hard. There is no drainage hole in the trunk, and the gap in the second picture will not cause water to flow into the interior. The black one is a plastic decorative panel.

If the warped plate of the taillight of this model is loose, it will not cause water leakage, because the fixing screw part behind the taillight is generally sealed, so even if the taillight warped plate is loose, it will not cause water to enter the trunk, so you need to check the backup. The glue strip of the box.

First, check whether the door drain is blocked (on the side under the door). If it is not blocked, check the sealing condition again.

Find the place where the water leaks. Check whether the trunk lid is deformed, whether the adhesive strip around it is aging, and use a water pipe.After watering, check which part has dripping water, or close the lid after entering the box to observe where the light is permeable, and make a mark.

What is the way to solve the problem of the door interior panel buckle

It may be that the fixing buckle of the door trim panel is broken. The owner can remove the door trim panel and replace the latch to solve the problem. In general, car interior panels and doors are fixed with screws and door clips. First, remove the screw that fixes the interior panel of the door, and then pry open the edge with a professional tool or screwdriver.

Hello. This card is all disposable. Just change it to one. I hope it can help you. I hope you can adopt it. Thank you.

Car door interior panel snap hole damage is relatively common, mainly caused by improper disassembly skills.It can be repaired. Please install the latch in the original position of the interior panel, even if it is loose, and then apply glue to fix it with AB glue. The strength after drying can meet the installation requirements.

How to disassemble the interior panel of the car door?

1. The following are the disassembly steps of the door interior panel: open the door that needs to be disassembled and disassemble the decorative cover of the inner handle of the door; use a small shape change cone into the gap between the decorative cover and the inner handle, and gently pry open the card inside; the disassembly of the screws fixing the door interior panel at the inner handle is t-30 Remove the screws with the spherne.

2. Use a flat opener to pry down the lower trim panel of the door handle, and open the back door from the middle down and outward to pry the first half. After removing the puller trim panel, you can see two black No. 8 hexagonal bolts inside. Screw them off with a socket wrench.

3. How to remove the interior panel of the car door: There is a snap in the interior panel. After pressing the snap, insert it along the interior panel with a flat screwdriver below and remove each buckle separately. The disassembly and installation of the interior panel requires the use of special tools to protect the connecting bolts and door decorations from damage.

How to remove the car interior panel

Use a screwdriver or plastic tool to gently remove the cover on the door handle and unscrew the screws. To remove the panel of the window controller, you usually need to use plastic tools to gently move the panel and remove the screws. Use a plastic tool to gently remove the edge of the interior panel of the door and gently pull out the board.

Wrap the soft cloth with a screwdriver and pry open the front door triangle protective plate from the upper snap position.Remove the front door triangle protective plate. The position of the snap and the fixing clip are shown in the figure. Remove the fastening screw of the front door lock and the fastening screw of the door with a Phillips screwdriver. Remove the snap on the front door decorative panel with a screwdriver.

First of all, use the warped plate to pry open the door horn cover along the edge of the door horn cover of the GAC Honda Accord car. After removing the door horn cover of the GAC Honda Accord car, you will find a Phillips screw. Just remove the Phillips screw with a screwdriver.

First of all, use a small shape change cone to slowly pry up from the edge of the decorative cover of the interior panel of the car door. Then gently disassemble the decorative cover. Be sure to pry slowly to avoid scratching the surface. Next, disassemble the screws of the fixing door interior panel.

Disassemble the piece of the pad, pull the big side with your hand, and force vertically upwards.Remove the door handle trim strip covering the T30 screw, start from the rear position of the door, and force forward all the way horizontally. Remove the T30 screws on the door, three for the front door and two for the back door.