The engine is seriously carbonized. The most common reason for car shaking is that the throttle valve is too dirty or the fuel injector has too much carbon.
Poor diesel atomization: the pressure adjustment of the fuel injector is too low, and the pressure regulator spring of the fuel injector is broken or stuck. The injector needle valve and valve seat are carbonised, and the needle valve is stuck or worn too much. The pressure reducing ring of the pump valve of Cummins is too worn, causing the injector to drip oil.
If the jitter in the idle state does not decrease due to the operation of the on-board air conditioner compressor, this jitter is likely to be caused by the aging of the engine foot, and the new foot needs to be replaced in time. Uneven tire weight is also one of the causes of shaking.
There is carbon accumulation in the combustion chamber, causing the gas ring of the piston ring to be stuck and poorly sealed. Oil sludge is produced in the lubrication system, which blocks the return hole of the oil ring and weakens the oil scraping performance. There is wear between the piston and the cylinder wall. The valve seal is corrosion-aging and the sealing performance is invalid.
1. Normally, CF level is used, such as the Great Wall Dragon King and Kunlun Tianhong. The brand doesn't matter. As long as it is genuine enough, the oil can be added.The diesel engine model S19S1100 is generally about 2 liters; the model 1125 is about 8 liters.
2. Depending on the car model, the amount of oil required is also different. Generally, three to four liters for small cars, and 4 to 5 liters for medium-sized cars. The general principle is that as long as it is added and does not overflow.
3. The amount of oil refueling the 6-cylinder engine oil for you is related to factors such as engine displacement, usage environment and usage habits, so it needs to be calculated according to the specific situation. Generally speaking, the oil capacity of a 6-cylinder engine is between 5-8 liters. For specific capacity, you can check the vehicle's instruction manual or consult a professional technician.
4. It depends on the diesel engine model, S195, S1100, generally about 2 liters, and 1125 is about 8 liters.Generally speaking, when adding oil, the oil should not exceed the upper scale of the oil ruler, and when using a diesel engine, the amount of oil should not be lower than the lower scale of the oil ruler.
5. Generally, small cars add three to four liters, and medium-sized cars add four to five liters. The choice of engine oil should be selected according to the requirements of the engine. There is no need to use too high-grade engine oil on engines with low requirements, nor to use lower-grade oil on engines with high requirements.
6. The diesel engine model S19S1100 is generally about 2 liters; the model 1125 is about 8 liters. The advantages of diesel engines are large torque and good economic performance. The working process of diesel engines has many similarities with that of gasoline engines. Each working cycle also goes through four strokes of air intake, compression, work and exhaust.
1. There are several reasons why the diesel engine is difficult to start: the diesel itself is not qualified and the wax content is high; the fuel injection atomization is not good; the fuel injection timing is not good; the airtightness is not good (piston ring, cylinder block grinding Damage or poor valve sealing), etc.
2. Fault performance: unable to start or difficult to start several times. Stop quickly after barely starting.
3. The temperature is insufficient. Due to the insufficient temperature of the engine, the mixture of fuel and air sprayed into the cylinder cannot be partially burned, and the exhaust pipe has white smoke. Therefore, after the locomotive starts, you should pay attention to the insulation of the water tank and use the middle throttle to operate, so that when the temperature of the locomotive reaches more than 50 degrees, the load should be gradually increased.
4. Fault phenomenon: turn on the ignition switch, turn the ignition switch to the starting position, and the engine does not start.
5. The oil road knot, or add negative 20 oil, and heat the oil-water separator may be fine. If it doesn't work, you can also call. Hey hey.. I'm on firewood.
Reason: The intake valve leaks or the valve gap is too small, causing the valve to close loosely after thermal expansion. The gap between the exhaust valves is too large, resulting in insufficient opening or completely inability to open the valve. There may be no air filter installed, or the air filter model is wrong.
The engine has serious carbon accumulation. The most common cause of idling jitter is excessive carbonisation of the throttle valve or fuel nozzle.
It may be leakage of the intake pipe or various valves. When the engine intake is not right, the mixed gas will be too thick or too thin, causing the engine to burn abnormally, and the engine idling and shaking with sound.
1. There are two types of D6114, type A and type B. The Type A machine is almost completely equivalent to Cummins' 3C. The Type B machine has replaced the Type A machine after AVL consulting and design. Now the Type A machine has been discontinued and all the Type B machines are produced.
2. The cylinder pad of type A is made of asbestos, and the cylinder pad of type B is made of metal. The ZQ and ZLQ cylinder liners of type A are made of a water-blocking coil (and the water-blocking coil is flat), and the B-type cylinder is made of 3 channels.
3. Shangchai 114 series has D6114, D9, D4114, SC8DK, SC9DK, SC9DF. The first three are national second models, and the latter three are national third models. D6114 cylinder diameter 114 stroke 135 displacement 3 liters, D9 cylinder diameter 114 stroke 144 displacement 8 liters.
When the Shangchai D6114 diesel engine is heated, the gap between the intake valve is about 0.45 cm; the gap of the exhaust valve is about 0.35 cm.
Shangchai 6114 valve clearance, which depends on the working conditions of the engine, and the gap of the inlet row is different. The valve clearance of Xinshangchai 6114 is: the intake gap is 0.05-0.08 and the exhaust gap is 0.08-0.12MM. I hope it will be helpful to you.
Compress the dead point of the positive cylinder and adjust the gap of the valve in the relaxed state; adjust the gap of other valves after turning 360 degrees.
Let's talk about the simplest and easiest way to understand: move the car according to the steering wheel of the car, and adjust the cylinder when the cylinder of the oil pump comes out.
*Country-specific HS code exemptions-APP, download it now, new users will receive a novice gift pack.
The engine is seriously carbonized. The most common reason for car shaking is that the throttle valve is too dirty or the fuel injector has too much carbon.
Poor diesel atomization: the pressure adjustment of the fuel injector is too low, and the pressure regulator spring of the fuel injector is broken or stuck. The injector needle valve and valve seat are carbonised, and the needle valve is stuck or worn too much. The pressure reducing ring of the pump valve of Cummins is too worn, causing the injector to drip oil.
If the jitter in the idle state does not decrease due to the operation of the on-board air conditioner compressor, this jitter is likely to be caused by the aging of the engine foot, and the new foot needs to be replaced in time. Uneven tire weight is also one of the causes of shaking.
There is carbon accumulation in the combustion chamber, causing the gas ring of the piston ring to be stuck and poorly sealed. Oil sludge is produced in the lubrication system, which blocks the return hole of the oil ring and weakens the oil scraping performance. There is wear between the piston and the cylinder wall. The valve seal is corrosion-aging and the sealing performance is invalid.
1. Normally, CF level is used, such as the Great Wall Dragon King and Kunlun Tianhong. The brand doesn't matter. As long as it is genuine enough, the oil can be added.The diesel engine model S19S1100 is generally about 2 liters; the model 1125 is about 8 liters.
2. Depending on the car model, the amount of oil required is also different. Generally, three to four liters for small cars, and 4 to 5 liters for medium-sized cars. The general principle is that as long as it is added and does not overflow.
3. The amount of oil refueling the 6-cylinder engine oil for you is related to factors such as engine displacement, usage environment and usage habits, so it needs to be calculated according to the specific situation. Generally speaking, the oil capacity of a 6-cylinder engine is between 5-8 liters. For specific capacity, you can check the vehicle's instruction manual or consult a professional technician.
4. It depends on the diesel engine model, S195, S1100, generally about 2 liters, and 1125 is about 8 liters.Generally speaking, when adding oil, the oil should not exceed the upper scale of the oil ruler, and when using a diesel engine, the amount of oil should not be lower than the lower scale of the oil ruler.
5. Generally, small cars add three to four liters, and medium-sized cars add four to five liters. The choice of engine oil should be selected according to the requirements of the engine. There is no need to use too high-grade engine oil on engines with low requirements, nor to use lower-grade oil on engines with high requirements.
6. The diesel engine model S19S1100 is generally about 2 liters; the model 1125 is about 8 liters. The advantages of diesel engines are large torque and good economic performance. The working process of diesel engines has many similarities with that of gasoline engines. Each working cycle also goes through four strokes of air intake, compression, work and exhaust.
1. There are several reasons why the diesel engine is difficult to start: the diesel itself is not qualified and the wax content is high; the fuel injection atomization is not good; the fuel injection timing is not good; the airtightness is not good (piston ring, cylinder block grinding Damage or poor valve sealing), etc.
2. Fault performance: unable to start or difficult to start several times. Stop quickly after barely starting.
3. The temperature is insufficient. Due to the insufficient temperature of the engine, the mixture of fuel and air sprayed into the cylinder cannot be partially burned, and the exhaust pipe has white smoke. Therefore, after the locomotive starts, you should pay attention to the insulation of the water tank and use the middle throttle to operate, so that when the temperature of the locomotive reaches more than 50 degrees, the load should be gradually increased.
4. Fault phenomenon: turn on the ignition switch, turn the ignition switch to the starting position, and the engine does not start.
5. The oil road knot, or add negative 20 oil, and heat the oil-water separator may be fine. If it doesn't work, you can also call. Hey hey.. I'm on firewood.
Reason: The intake valve leaks or the valve gap is too small, causing the valve to close loosely after thermal expansion. The gap between the exhaust valves is too large, resulting in insufficient opening or completely inability to open the valve. There may be no air filter installed, or the air filter model is wrong.
The engine has serious carbon accumulation. The most common cause of idling jitter is excessive carbonisation of the throttle valve or fuel nozzle.
It may be leakage of the intake pipe or various valves. When the engine intake is not right, the mixed gas will be too thick or too thin, causing the engine to burn abnormally, and the engine idling and shaking with sound.
1. There are two types of D6114, type A and type B. The Type A machine is almost completely equivalent to Cummins' 3C. The Type B machine has replaced the Type A machine after AVL consulting and design. Now the Type A machine has been discontinued and all the Type B machines are produced.
2. The cylinder pad of type A is made of asbestos, and the cylinder pad of type B is made of metal. The ZQ and ZLQ cylinder liners of type A are made of a water-blocking coil (and the water-blocking coil is flat), and the B-type cylinder is made of 3 channels.
3. Shangchai 114 series has D6114, D9, D4114, SC8DK, SC9DK, SC9DF. The first three are national second models, and the latter three are national third models. D6114 cylinder diameter 114 stroke 135 displacement 3 liters, D9 cylinder diameter 114 stroke 144 displacement 8 liters.
When the Shangchai D6114 diesel engine is heated, the gap between the intake valve is about 0.45 cm; the gap of the exhaust valve is about 0.35 cm.
Shangchai 6114 valve clearance, which depends on the working conditions of the engine, and the gap of the inlet row is different. The valve clearance of Xinshangchai 6114 is: the intake gap is 0.05-0.08 and the exhaust gap is 0.08-0.12MM. I hope it will be helpful to you.
Compress the dead point of the positive cylinder and adjust the gap of the valve in the relaxed state; adjust the gap of other valves after turning 360 degrees.
Let's talk about the simplest and easiest way to understand: move the car according to the steering wheel of the car, and adjust the cylinder when the cylinder of the oil pump comes out.
*Global trade certificate verification
author: 2024-12-23 22:20Trade data for industrial raw materials
author: 2024-12-23 21:58Ceramics imports HS code mapping
author: 2024-12-23 21:35HS code-driven route-to-market planning
author: 2024-12-23 21:15Aggregated global trade insights dashboard
author: 2024-12-23 20:41Agriculture import export insights
author: 2024-12-23 22:25Metal scrap HS code classification
author: 2024-12-23 22:24Real-time shipment data alerts
author: 2024-12-23 22:09HS code-based vendor qualification
author: 2024-12-23 21:25Worldwide trade corridor mapping
author: 2024-12-23 20:51457.85MB
Check226.68MB
Check583.51MB
Check863.16MB
Check722.15MB
Check722.16MB
Check264.62MB
Check889.23MB
Check373.23MB
Check973.98MB
Check217.31MB
Check178.38MB
Check632.18MB
Check284.69MB
Check563.91MB
Check285.26MB
Check565.26MB
Check318.71MB
Check796.72MB
Check415.87MB
Check855.33MB
Check277.51MB
Check875.63MB
Check145.24MB
Check333.29MB
Check955.32MB
Check984.88MB
Check652.17MB
Check927.16MB
Check898.84MB
Check657.72MB
Check931.41MB
Check986.15MB
Check236.81MB
Check994.39MB
Check145.65MB
CheckScan to install
Country-specific HS code exemptions to discover more
Netizen comments More
2088 Raw tobacco HS code tracking
2024-12-23 22:33 recommend
417 How to calculate landed costs accurately
2024-12-23 22:26 recommend
2606 Global trade shipping route optimization
2024-12-23 22:12 recommend
2726 Latin America trade data insights
2024-12-23 20:45 recommend
2940 Global trade intelligence for banking
2024-12-23 20:20 recommend