HVAC equipment HS code mapping

List of the catalog of this article:

• 1. How to disassemble the JAC 4102 engine oil san?
• 2, How to disassemble the Haval f5 engine oil sap
• 3 , How to remove the oil sale?
• 4、Honda crv2.0 How to disassemble the engine oil span

How to disassemble the JAC 4102 engine oil san?

In order to avoid bending of the oil span, the bolts of the oil span should be unstwewed from both sides to the middle diagonally, and then put the oil span on the bracket. Any bending of the oil san or damage to the installation surface will cause oil leakage. Therefore, before installing the oil span, be sure to remove the old sealing gaskets and gaskets.

The way to disassemble the engine oil span is to clean the oil first, then unscrew off the circle of hexagonal screws on the oil span in turn, and knock down the oil pan. The oil sup is the lower half of the crankcase, also known as the lower crankcase.

Find aPrepare an oil iron basin or an empty barrel. Find the tool in the toolbox to deal with the oil pan shell, such as opening, movable plate hand, plum blossom, sleeve to remove the oil pan shell rose, unswire out the large rose, and let the oil flow out into the plate, into the barrel or, until the flow is finished.

Remove the fixing screw of the cylinder head, note that the screw should be cross-spinned from both ends to the middle, and remove the screw in 3 times. 2) Lift the cylinder head. Remove the cylinder pad and pay attention to the installation direction of the cylinder pad. Loosen the oil release screw of the oil span shell to release the oil in the oil span shell.

If it can be disassembled, you can put down the Yuanbao beam a little, and the oil pan can be removed [If there is a problem with the car, ask the car master. 4S store professional technician, 10 minutes to solve.

Hello, if you want to remove the oil span screw, use the carWhen the lifter is lifted, you can unswew it with a wrench. It is not recommended to put oil from here. If it takes a long time, it is easy to slip.

How to disassemble the Haval f5 engine oil span

1. Disassembly of the engine oil span The unloading method is to first clean the oil, then unscrew off the circle of hexagonal screws on the oil sap in turn, and knock down the oil sap.The oil sup is the lower half of the crankcase, also known as the lower crankcase.

2. Find an oil iron basin or an empty barrel to prepare. Find the tool to deal with this oil pan big rose in the toolbox, such as opening, movable plate hand, plum blossom, sleeve to remove the oil pan rose, unswew out the big rose, and let the oil flow into the plate, into the barrel or, until the flow is finished.

3. If you want to remove the oil span of the gearbox, you need to remove the oil span of the gearbox and remove the oil seal with a hexagon wrench. If the gearbox changes the oil, it is recommended to use a circulation machine to change the oil thoroughly. If you want to remove the engine oil san, you don't need to remove the transmission oil san, which will be convenient.

4. Drive the vehicle to the flat ground, lift the vehicle with a jack, and put the oil leakage plate under the vehicle to collect the leaking oil.In the engine compartment, remove the pressure plate and clutch disc of the clutch disc with a screwdriver, and then remove the clutch disc from the gearbox output shaft.

5. Hello, for this oil pan shell screw, lift the car lifter and unscrew it with a wrench. It is not recommended to put the oil from here. If it takes a long time, it is easy to slip.

6. There are also screws inside. Top the engine, loosen the six large screws of the Yuanbao beam, loosen a circle of screws, and the two are hidden above the Yuanbao beam. Check carefully, the screws at the four corners of the oil bottom are hidden, and the screws on this side of the motor are obvious. You can take off the engine oil span shell by prying the joints with a stick and knocking on the vibrating oil ruler guide.

How to remove the oil sale?

First, clean the oil, and then unscrew off the circle of hexagonal screws on the oil sap in turn, and knock down the oil sap. The oil sup is the lower half of the crankcase, also known as the lower crankcase.

Step 1 Prepare tools Before disassembling the Cruze oil pan, we need to prepare some necessary tools, including wrenches, Phillips screwdrivers, rubber hammers, electric screwdrivers, etc. These tools can help us disassemble the oil sank more conveniently.

Screw off a circle of hexagonal screws on the oil span. First, clean the oil, and then unscrew off the circle of hexagonal screws on the oil sap in turn, and knock down the oil sap.

To remove the Mingjue mg3 oil pan, you need to use a socket wrench to unscrew the screw that fixes the oil span first. The specific operation steps for disassembling the Mingjue mg3 oil span are as follows: loosen the fixing screw in the upper left corner of the Mingjue mg3 oil span.Loosen the fixing screw in the upper corner of the lower right corner of the Mingjue mg3 oil pan shell.

A set of auto repair tools should be prepared before disassembling the Passat oil pan. Start the car and carefully drive the car to the lifting rack. After the driver comes down, start the lifting button and lift the car to the air for easy operation.

How to disassemble and install the Passat b5 oil pan shell?

1. The replacement process of the old Passat b5 oil pan is as follows: first remove the oil release screw of the oil pan. Prepare a clean empty barrel, remove the oil release screw of the oil pan, and use the empty barrel to catch the discharged oil. Basically unscrew the screws around the oil span and remove the oil sump. Apply sealant evenly around the new oil san shell.

2. The disassembly and installation method of the Passat oil span is as follows: a set of auto repair tools should be prepared before disassembling the Passat oil span.Start the car and carefully drive the car to the lifting rack. After the driver comes down, start the lifting button and lift the car to the air for easy operation.

3. The disassembly and installation steps of the Passat oil sap are as follows: Step 1: Remove the front engine bracket and remove the six bolts of the front Yuanbao beam with a wrench, distributed in three on the left and right sides.

4. There is no picture. The method is as follows: park the vehicle on the flat ground and make sure that the engine has cooled down. Use a jack to lift the vehicle so that it can safely enter the bottom. Find the oil san at the bottom of the vehicle, which is usually located directly below the engine. Use a wrench or wrench sleeve to remove the screw on the oil sup.

5. The processing steps of the oil pan are as follows: finish the oil first. Remove the oil spre screw. Remove the old cushion and wipe off the dust that fell inside.Just bake the newly bought cushion with a wooden fire until it is soft, because it's cold now and it's not easy to cover it directly. It is to cover the soft cushion on the oil pan shell.

Disassembly and installation steps of Passat oil sup?

1. The disassembly and installation steps of the Passat oil pan are as follows: Step 1: Remove the front engine bracket, remove the six bolts of the front Yuanbao beam with a wrench, and distribute them in three on the left and right sides.

2. The replacement process of the old Passat b5 oil pan is as follows: remove the oil release screw of the oil pan first. Prepare a clean empty barrel, remove the oil release screw of the oil pan, and use the empty barrel to catch the discharged oil. Basically unscrew the screws around the oil span and remove the oil sump. Apply sealant evenly around the new oil san shell.

3. First, unscrew the oil release screw of the oil pan shell. After unscrewing the oil release screw of the oil pan, use a clean empty barrel to catch the released oil. Unscrew all the screws around the oil sap. The oil sall can be removed. Apply sealant evenly around the new oil pan shell.

Honda crv2.0 engine oil pan disassembly method

1. First, put the car up, and then find a large vessel under the car in case of receiving waste oil. Remove the inside and shell of the gearbox with a suitable screwdriver. At this time, some transmission oil will flow out. Pay attention to avoid it. Remove the oil. Remove the lower guard plate of the engine. Remove the oil san screw.

2. Engine oilThe method of disassembly of the bottom shell is to clean the oil first, then unscrew off the circle of hexagonal screws on the oil sup in turn, and knock down the oil sup. The oil sup is the lower half of the crankcase, also known as the lower crankcase.

3. The first step: run the engine to reach the working temperature. Then pull up the vehicle, pull the handbrake, and squeeze the front wheel with a wooden wedge. Step 2: Put the old fuel tank under the oil tank, find the oil release bolt of the oil tank, slowly unstwew the oil bolt, and pay attention not to touch the hot oil. Let the oil drip for a while.

4. The method of removing the engine oil pan is to clean the oil first, and then unscrew off a circle of hexagonal screws on the oil pan in turn, and knock down the oil pan! This method replaces and cleans from the root, and can also treat the dirty oil filter.