Top trade data trends reports

List of the table of contents of this article:

• 1, How to stick the car threshold strip?
• 2 、 Is it necessary to install the car threshold strip?Top trade data trends reports

How to stick the car threshold strip?

1. First of all, you need to met the long and short position of the threshold bar. When installing the threshold strip, you need to pull out the adhesive strip on the door first. When pasting, use the adhesive to clean off the wax from the factory of the plastic parts, and then apply a little adhesive on the backing adhesive. Stick it tightly, and then press the adhesive strip back to the inner threshold.

2. First of all, it is necessary to find the exact position before pasting the car threshold strip. The threshold strip is located directly below the door, which is a place where shoes are easy to touch when getting on and off. In order to avoid being rubbed, a piece of plastic plate is usually wrapped. Secondly, wipe the adhesive position of the threshold strip with a wet cloth.

3. First of all, find the right position. The threshold bar is located directly below the door, which is the place where shoes are easy to touch when getting on and off. Secondly, keep the contact surface clean, so as to ensure that the adhesion is firm. You can use a fiber-free cloth dipped in 50% alcohol, isopropyl alcohol, acetone or toluene solution to clean it.

4. Externally long. The car threshold strip is externally long and internally short. The external threshold of the car is pasted on the paint, and the internal threshold of the car is pasted on the plastic. So it is built-in short.

5. Wipe the place that needs to be posted directly with a towel, and then stick the threshold strip directly on it.

6. There are several suggestions for installing the threshold strip as follows: use a special binder for cars. First, you need to clean the bonding place, and then heat the layer that needs to be bonded with a hot air gun and then bond it at one time. There are also other adhesives, such as glass glue, and it is better to use neutral, acidic corrosion car paint (not recommended, because the vehicle is not glass).

How to remove the car threshold?

Chang'an 75plus threshold strip is blown and dismantled by a hot fan. Chang'an 75plus threshold strip can be removed. You can blow it with a hot fan, heat it with a hair dryer from the upturned place, and pull it out after the glue is soft, and it will not leave any traces and glue.

The disassembly method of Xuanyi classic threshold strip is as follows: first, remove the panel of the glass take-off device, which is generally fixed with a snap type and slowly pry it out.

First, use a flat opener to pry down the lower trim panel of the door handle, and pry the first half when opening the back door from the middle down and then outward. Secondly, after removing the puller trim panel, you can see two black No. 8 hexagonal bolts inside. Screw them off with a socket wrench.

Pry down the lower trim panel of the door handle with a flat opener, and open the back door from the middle down and then outward to pry the first half. After removing the puller trim panel, you can see two black No. 8 hexagonal bolts inside. Screw them off with a socket wrench.

Is it necessary to install the car threshold strip

1. There is no need to install the car threshold strip. If you want to install it, you can also install it. The threshold mentioned here actually refers to the bottom edge below the door, which is part of the body frame. In the event of a side collision, the bottom edge and the b-pillar can protect the members of the car.

2. It is actually necessary to install the vehicle threshold strip. The vehicle threshold strip, also known as the welcome pedal, is the position directly below the door. The vehicle threshold can effectively protect the wear-resistant parts of your beloved car.

3. It is still necessary to install the threshold strip, because the threshold strip can not only protect the threshold of the car from damage, especially the scratches when getting on and off the car, which must play the function of anti-collision and anti-rusion, and the exquisite and gorgeous appearance is also a decorative element, which is a must-choose basic interior for car enthusiasts.

4. Yes, it can be installed. After installation, it can effectively protect the threshold of the vehicle. The threshold is a very fragile part, which is very easy to touch when getting on and off. After a long period of wear, the paint will fall off and bump. It is more troublesome to repair in the later stage, and pasting the threshold strip can be effectively avoided.

5. It can be installed. After installation, the vehicle threshold is effectively protected. The threshold part is a vulnerable part, which is very easy to touch when getting on and off. After a long time of use and wear, there will be problems of paint loss and bumping. Later repair is more troublesome, and pasting the threshold strip can be effectively avoided.