Fault analysis: When the idle contact is disconnected, the ECU determines that the engine is in a partial load state.At this time, the ECU determines the amount of fuel injection according to the air flow meter and the crankshaft speed signal. At this time, the engine is working under idle conditions, with less air intake, resulting in excessive mixing gas and increasing speed.
The selection of engine oil should be selected according to the requirements of the engine. There is no need to use too high-grade engine oil on engines with lower requirements, nor to use lower-grade oil on engines with higher requirements.
Valvane sound: The length of valve sound has a lot to do with the quality of the oil. Generally, all-synthetic oil has good fluidity and strong protection ability. Generally, it sounds for about 1-3 minutes, while ordinary oil sounds longer. At the same time, it is also related to the carbon accumulation of the valve.
1, displacement, power output.Displacement: The displacement of Chery twin-cylinder 600 is 600 ml, while the displacement of 272 is 272 ml, and the engine displacement of Chery twin-cylinder 600 is larger.
2. Dispagment difference: The displacement of Chery twin-cylinder 600 is small, only 350cc, while Chery 272 has a large displacement, more than 1000cc. The size of the displacement directly affects the power output and fuel economy of the engine.
3. Recently, it has been revealed that Chery has developed an engine with 0L displacement, turbocharged air intake, with a power data of up to 254 horsepower and 385 Nm, which is enough to benchmark the luxury brand high-power 0T engine. However, this engine is not a joint venture, but independently developed by Chery.
4. Engine 230t engine displacement 5T, torque 230 Nm, maximum power 115KW.290t engine displacement 6T, torque 290 Nm, maximum power 145KW. 290T is equipped with engine start-stop technology.
5. The 0TGDI engine code-named F4J20 launched by Chery this time adopts in-cylinder direct injection technology, with a maximum power of 187kW (240 horsepower) and a peak torque of 385N·m. It is reported that the engine will be the first to be installed on the flagship SUV Starway VX and matched with the 6TGDI engine.
6. The fuel consumption is lower, and the fuel consumption under working conditions is as low as 5L per 100 kilometers. The maximum range of a full tank of oil is about 700 kilometers. The Chery twin-cylinder 272 is an electric gasoline engine equipped with Chery cars. The horsepower of Chery's 272 twin-cylinder engine is 350 horsepower, and the speed can reach 120km per hour, which is deeply loved by young people.
1 , the coolant entering the engine cylinder block will affect the milky white of the oil. The coolant enters the cylinder because the cylinder pad is not good, which will affect the sealing performance. The cylinder pad must be replaced, otherwise it will affect the operation of the engine.
2. When the coolant enters the cylinder block of the engine, it will affect the engine oil to become milky white. The coolant entering the cylinder is due to the poor cylinder pad, which affects the sealing problem. The cylinder pad needs to be replaced from a new one, otherwise it will affect the operation of the engine.
3. If the cylinder pad is damaged, it needs to be replaced. In addition, this problem should be dealt with as soon as possible. A long time will cause the oil to emulsify, and the harm to the engine will increase. In this way, the continuous consumption of antifreeze will make the operating temperature of the engine continue in a high range, which is also a factor that hinders the normal operation of the engine.
4. When there is a problem with the vehicle, it can enter the engine. The radiator of the engine oil filter is cooled by coolant.In addition, the sealing inside the cylinder head of the car also has water circulation and oil lubrication channels. If there is a problem with this part, it can cause cold blood to enter the engine. So.
5. Generally speaking, the antifreeze enters the engine mainly with the oil entering the engine, and the emulsification reaction occurs when the coolant is mixed with the oil. After the oil is emulsified, the engine cannot be better protected, and it will also cause the phenomenon of pulling the cylinder to the engine.
Chery twin-cylinder 272 is an electric-injected gasoline engine equipped with Chery cars. The horsepower of Chery's 272 twin-cylinder engine is 350 horses, with a speed of up to 120km per hour, is deeply loved by young people.
V2 or straight 2 twin-cylinder is usually 75-90 horsepower, which is mostly used in street cars, while sports cars are usually in-line 4-cylinder engines. In the early days, the straight four 600 has a maximum of 100-110 horsepower, and now it is basically above 120 horsepower. Generally, after 2005, it is all electric injection fuel supply.
It doesn't depend on the displacement alone. It depends on how many cylinders there are, generally a single cylinder, and how many strokes and the number of gas valves. Now it is basically electric spraying. The power of a 600-distragment motorcycle should be 20-30KW, about 40 horsepower. For a racing engine with a speed of 10,000 speed, it is about 70 horsepower, and the price can't be said, because the difference is too big.
Dispast, power output. Displacement: The displacement of Chery twin-cylinder 600 is 600 ml, while the displacement of 272 is 272 ml, and the engine displacement of Chery twin-cylinder 600 is larger.
1. The differences between Chery twin-cylinder 600 and 272 are as follows: Chery twin-cylinder 600cc engine, with iHEC (intelligent effect) combustion Burning technology, electronically controlled fuel multi-point injection, lower fuel consumption, and the fuel consumption under working conditions is as low as 5L per 100 kilometers. The maximum range of a full tank of oil is about 700 kilometers.
2. It is generally appropriate to add oil between the upper and lower limits of the oil ruler, and do not fall below the middle scale, because the high temperature of the engine can make the oil thinner when driving at high speed. If the amount of oil is small, it will reduce the lubrication effect and cooling effect. Practice proves that it is ideal to add oil below 1/4 of the upper limit.
3. Finally, turn off the engine and check the amount of oil repeatedly.Deal with old engine oil and filter elements according to local regulations. Oil change DIY - not only saves time and money, but also helps you find some latent problems (such as liquid leakage) in the vehicle. Oil change DIY - not only learn car maintenance techniques, but also increase the affection between friends and family members.
4. Differences in engine type and displacement. Engine type: Chery twin-cylinder 600 is a twin-cylinder engine with only two cylinders, while Chery 272 is a four-cylinder engine with four cylinders, which produces more power during the working process.
5. Just add 3 liters of oil to the standard of 600 engine oil. The appearance design of Jinqing Chase 600 is based on the Benelli Yellow Dragon 600 as the prototype, and a new development and design of the V-shaped brow bone of the car is sharp.The LED light source of the whole car is atmospheric and beautiful, and the whole shows a strong forward-leaning shape. The water tank adds the flank design and the body spraying is also more exquisite.
6. It depends on the diesel engine model, S195, S1100, generally about 2 liters, and 1125 is about 8 liters. Generally speaking, when adding oil, the oil should not exceed the upper scale of the oil ruler, and when using a diesel engine, the amount of oil should not be lower than the lower scale of the oil ruler.
Trade intelligence for industrial equipment-APP, download it now, new users will receive a novice gift pack.
Fault analysis: When the idle contact is disconnected, the ECU determines that the engine is in a partial load state.At this time, the ECU determines the amount of fuel injection according to the air flow meter and the crankshaft speed signal. At this time, the engine is working under idle conditions, with less air intake, resulting in excessive mixing gas and increasing speed.
The selection of engine oil should be selected according to the requirements of the engine. There is no need to use too high-grade engine oil on engines with lower requirements, nor to use lower-grade oil on engines with higher requirements.
Valvane sound: The length of valve sound has a lot to do with the quality of the oil. Generally, all-synthetic oil has good fluidity and strong protection ability. Generally, it sounds for about 1-3 minutes, while ordinary oil sounds longer. At the same time, it is also related to the carbon accumulation of the valve.
1, displacement, power output.Displacement: The displacement of Chery twin-cylinder 600 is 600 ml, while the displacement of 272 is 272 ml, and the engine displacement of Chery twin-cylinder 600 is larger.
2. Dispagment difference: The displacement of Chery twin-cylinder 600 is small, only 350cc, while Chery 272 has a large displacement, more than 1000cc. The size of the displacement directly affects the power output and fuel economy of the engine.
3. Recently, it has been revealed that Chery has developed an engine with 0L displacement, turbocharged air intake, with a power data of up to 254 horsepower and 385 Nm, which is enough to benchmark the luxury brand high-power 0T engine. However, this engine is not a joint venture, but independently developed by Chery.
4. Engine 230t engine displacement 5T, torque 230 Nm, maximum power 115KW.290t engine displacement 6T, torque 290 Nm, maximum power 145KW. 290T is equipped with engine start-stop technology.
5. The 0TGDI engine code-named F4J20 launched by Chery this time adopts in-cylinder direct injection technology, with a maximum power of 187kW (240 horsepower) and a peak torque of 385N·m. It is reported that the engine will be the first to be installed on the flagship SUV Starway VX and matched with the 6TGDI engine.
6. The fuel consumption is lower, and the fuel consumption under working conditions is as low as 5L per 100 kilometers. The maximum range of a full tank of oil is about 700 kilometers. The Chery twin-cylinder 272 is an electric gasoline engine equipped with Chery cars. The horsepower of Chery's 272 twin-cylinder engine is 350 horsepower, and the speed can reach 120km per hour, which is deeply loved by young people.
1 , the coolant entering the engine cylinder block will affect the milky white of the oil. The coolant enters the cylinder because the cylinder pad is not good, which will affect the sealing performance. The cylinder pad must be replaced, otherwise it will affect the operation of the engine.
2. When the coolant enters the cylinder block of the engine, it will affect the engine oil to become milky white. The coolant entering the cylinder is due to the poor cylinder pad, which affects the sealing problem. The cylinder pad needs to be replaced from a new one, otherwise it will affect the operation of the engine.
3. If the cylinder pad is damaged, it needs to be replaced. In addition, this problem should be dealt with as soon as possible. A long time will cause the oil to emulsify, and the harm to the engine will increase. In this way, the continuous consumption of antifreeze will make the operating temperature of the engine continue in a high range, which is also a factor that hinders the normal operation of the engine.
4. When there is a problem with the vehicle, it can enter the engine. The radiator of the engine oil filter is cooled by coolant.In addition, the sealing inside the cylinder head of the car also has water circulation and oil lubrication channels. If there is a problem with this part, it can cause cold blood to enter the engine. So.
5. Generally speaking, the antifreeze enters the engine mainly with the oil entering the engine, and the emulsification reaction occurs when the coolant is mixed with the oil. After the oil is emulsified, the engine cannot be better protected, and it will also cause the phenomenon of pulling the cylinder to the engine.
Chery twin-cylinder 272 is an electric-injected gasoline engine equipped with Chery cars. The horsepower of Chery's 272 twin-cylinder engine is 350 horses, with a speed of up to 120km per hour, is deeply loved by young people.
V2 or straight 2 twin-cylinder is usually 75-90 horsepower, which is mostly used in street cars, while sports cars are usually in-line 4-cylinder engines. In the early days, the straight four 600 has a maximum of 100-110 horsepower, and now it is basically above 120 horsepower. Generally, after 2005, it is all electric injection fuel supply.
It doesn't depend on the displacement alone. It depends on how many cylinders there are, generally a single cylinder, and how many strokes and the number of gas valves. Now it is basically electric spraying. The power of a 600-distragment motorcycle should be 20-30KW, about 40 horsepower. For a racing engine with a speed of 10,000 speed, it is about 70 horsepower, and the price can't be said, because the difference is too big.
Dispast, power output. Displacement: The displacement of Chery twin-cylinder 600 is 600 ml, while the displacement of 272 is 272 ml, and the engine displacement of Chery twin-cylinder 600 is larger.
1. The differences between Chery twin-cylinder 600 and 272 are as follows: Chery twin-cylinder 600cc engine, with iHEC (intelligent effect) combustion Burning technology, electronically controlled fuel multi-point injection, lower fuel consumption, and the fuel consumption under working conditions is as low as 5L per 100 kilometers. The maximum range of a full tank of oil is about 700 kilometers.
2. It is generally appropriate to add oil between the upper and lower limits of the oil ruler, and do not fall below the middle scale, because the high temperature of the engine can make the oil thinner when driving at high speed. If the amount of oil is small, it will reduce the lubrication effect and cooling effect. Practice proves that it is ideal to add oil below 1/4 of the upper limit.
3. Finally, turn off the engine and check the amount of oil repeatedly.Deal with old engine oil and filter elements according to local regulations. Oil change DIY - not only saves time and money, but also helps you find some latent problems (such as liquid leakage) in the vehicle. Oil change DIY - not only learn car maintenance techniques, but also increase the affection between friends and family members.
4. Differences in engine type and displacement. Engine type: Chery twin-cylinder 600 is a twin-cylinder engine with only two cylinders, while Chery 272 is a four-cylinder engine with four cylinders, which produces more power during the working process.
5. Just add 3 liters of oil to the standard of 600 engine oil. The appearance design of Jinqing Chase 600 is based on the Benelli Yellow Dragon 600 as the prototype, and a new development and design of the V-shaped brow bone of the car is sharp.The LED light source of the whole car is atmospheric and beautiful, and the whole shows a strong forward-leaning shape. The water tank adds the flank design and the body spraying is also more exquisite.
6. It depends on the diesel engine model, S195, S1100, generally about 2 liters, and 1125 is about 8 liters. Generally speaking, when adding oil, the oil should not exceed the upper scale of the oil ruler, and when using a diesel engine, the amount of oil should not be lower than the lower scale of the oil ruler.
HS code-based supplier development
author: 2024-12-23 22:55HS code compliance training modules
author: 2024-12-23 22:43Middle East trade compliance platform
author: 2024-12-23 22:13Country-specific HS code exemptions
author: 2024-12-23 20:48HS code-based quality control checks
author: 2024-12-23 20:37Global supply chain partner networks
author: 2024-12-23 22:11Refined metals HS code references
author: 2024-12-23 21:44Global trade tender evaluation tools
author: 2024-12-23 21:03HS code-based supply risk mitigation
author: 2024-12-23 21:02Chemical HS code alerts in EU markets
author: 2024-12-23 20:29872.57MB
Check372.36MB
Check338.76MB
Check795.37MB
Check697.32MB
Check182.69MB
Check626.25MB
Check876.46MB
Check762.49MB
Check653.12MB
Check799.48MB
Check229.45MB
Check885.45MB
Check151.57MB
Check593.29MB
Check372.48MB
Check715.38MB
Check482.14MB
Check367.55MB
Check814.46MB
Check941.92MB
Check486.49MB
Check844.88MB
Check684.39MB
Check648.21MB
Check815.42MB
Check874.84MB
Check451.53MB
Check691.98MB
Check596.24MB
Check947.19MB
Check932.99MB
Check586.74MB
Check371.63MB
Check511.97MB
Check742.27MB
CheckScan to install
Trade intelligence for industrial equipment to discover more
Netizen comments More
1285 HS code-based invoice matching
2024-12-23 22:59 recommend
2654 How to identify monopolistic suppliers
2024-12-23 22:39 recommend
2511 Global trade barrier analysis
2024-12-23 22:31 recommend
2663 Region-specific HS code advisory
2024-12-23 21:44 recommend
2039 How to analyze competitor shipping routes
2024-12-23 21:14 recommend