Supplier onboarding with data analytics

List of catalogs of this article:

• 1,Supplier onboarding with data analytics RongweiHow to fix the 550 engine cover
• 2, May I ask how the aircraft engine is fixed on the wing?
• 3, What is the fixation between the car engine and the chassis
• 4, What will you do to check and fasten the engine bracket?

How to fix the Rongwei 550 engine cover

First, open the cover of the front hood of the car, and you can see that the support rod of the hood has support points at the upper and lower ends. Secondly, find the latch at the top of the car engine cover support rod.Finally, just install the Rongwei 550 engine bracket.

Whether the screw needs to be tightened depends on the situation. The rubber pad should not be too tight, the asbestos pad can be tightened, and the glue directly without the pad should also be tightened.

The Rongwei 550 valve chamber cover is sealed with adhesive. First, remove the valve chamber cover screw diagonally from both sides to the middle, pry the valve chamber cover with a one-word knife, and take out the valve chamber cover cushion.

The engine underguard screw is loose. A relatively common minor fault, tightening or adjusting the under-engine guard screw. The engine claw pad is aging. The claw pad plays a role in supporting the engine, and can only be replaced after aging. The plastic parts in the engine compartment are loose. For example, the engine cover, intake pipe, etc., just tighten it.

Enter firstGo to the main driver's seat of the Rongwei 550 car and find the front cover switch under the left side of the main driver's seat. Next, just pull the front hood switch of the Rongwei 550 car, and the latch of the front cover of the car can pop up.

With a wrench in the driver's seat, the engine cover will rise a little. When you walk to the front, you squat down and have a round button on the left side in the middle of the front. Press it down with a little force and lift the engine cover with one hand.

May I ask how the aircraft engine is fixed on the wing?

1. That is, when the air passes through the upper surface of the wing, the flow rate is large and the pressure is small; when it passes through the lower surface, the flow rate is small and the pressure is strong. Therefore, at this time, the aircraft will have an upward synergy, that is, the upward lift. Due to the existence of the lift, the aircraft can leave the ground and fly in the air.The wing-hanging layout starts from the most common wing-hanging layout.

2. As for hanging on the wing, it is just an engine installation method. In fact, the engine can be completely installed in other parts of the head of the aircraft, such as the tail (such as McDow 80). Hanging on the wings is just a better installation method at present, because in this way, it is far from the fuselage, and the noise and vibration that passengers receive are less.

3. The wings are close to the ground, and the transmitter is located behind the fuselage. For aviation engines, the first to be used is the piston engine. Its working principle is that the piston carries gas pressure, makes repeated movements in the cylinder, and transforms this movement into the rotational activity of the crankshaft according to the connecting rod.

4. There are many installation positions of aircraft engines, and the specific choice is related to the type of engine and the needs of the aircraft.The engine of a propeller aircraft is installed on the front or wing of the aircraft with the propeller. Most civil passenger and cargo aircraft install the engine under the wing or in the external short compartment at the tail of the fuselage.

5. Fuselage - The main function of the fuselage is to load occupants, passengers, weapons, cargo and various equipment, and to connect other parts of the aircraft such as wings, tails and engines into a whole. Tail - The tail includes horizontal tail and vertical tail.

6. The reason why the engine of a large passenger plane should be installed under the wing: First of all, this can offset the upward torque generated on the wing due to the lift, so as to achieve torque balance.

What is used to fix between the car engine and the chassis

1. The brackets connecting the engine and the axle are also fixed with bolts respectively, and the cushion plays a buffer role between the two brackets. Due to the needs of NVH, civil vehicles must cut off the transmission of engine vibration to the frame, basically soft coupling, relying on a device called engine suspension system.

2. The automobile engine and body are connected by mechanical rubber fulcrum or hydraulic rubber fulcrum.Connect, so as to achieve the effect of reducing the vibration of the engine. If the engine and the body are directly connected by screws, the vibration of the engine will be transmitted to the car, affecting the comfort of the occupans in the car.

3. The car engine and the car body are connected by mechanical rubber protection or hydraulic rubber protection, which can reduce the impact of engine vibration. If the engine and the body are directly connected by screw rigidity, the power output by the engine will drive the wheels through a series of power transmission devices.

4. The function of the transmission system The power emitted by the car engine is transmitted to the driving wheels by the transmission system.

5. These suspensions all belong to "independent suspension". The concept is that the rocker arm connecting rod of each group of wheels is independently fixed to the chassis structure of the vehicle, in a veryThey will not restrain each other (affecting the wheel posture) within the large limit, but it cannot be done without independent suspension.

What will you do to check and fasten the engine bracket?

Air filter, remove or remove the sediment of each filter, and remove the oil in the container.

When the engine seat fails, the engine idles and shakes in the car. The engine will shake violently during operation. If the seat fails, there will be danger during driving. If the base is broken, the car owners must replace it immediately. The engine and gearbox are assembled in the engine compartment. In order to ensure the normal operation of the engine, certain support and fixation are required.

First of all, you can use the pryPry open the engine foot with a stick to see if there are aging cracks and large intervals, or support the engine with a jack below to start the vehicle to the cab. Whether the shaking disappears and decreases significantly, if so, you should consider replacing the engine bracket in time.

Check the bracket: Open the hood and check whether the bracket is loose, damaged or deformed. If a problem is found, it may be necessary to replace the bracket or repair it. Fastening bolts: Check whether the bolts of the bracket are fastened. If the bolt is loose, use appropriate tools to tighten it to ensure that the bracket is firm.

Check the possibility of the engine bracket: First, check the engine bracket to ensure that it is intact, not loose or damaged. For the damaged bracket, it needs to be repaired or replaced in time. In addition, check the fasteners on the engine bracket to make sure that they are firm and will not break.